• RoboSlide

• Motor - 12V DC
• Cycles - 70 / day with transformer, transformer uses low voltage wire and can be installed up to 1000' from the gate operator.
• Maximum Gate Size/Weight - Up to 20' length, gate weighing up to 800 lbs.
• Gate Traveling Time - Opens gate at 11 inches per second.
• Limit Switch System - Uses a precise limit switch system that reduces stress and creates a constantly smooth operation.
• Chassis - 1/8" sheet metal, welded and fully plated.
• Cover - Heavy-duty weatherproof polyethylene plastic.
• Gear Box - 30 to 1 ratio gear reducer in an oil bath, delivers smooth and quiet operation.
• Manual Disconnect - Emergency chain release available for manual operation.
• Warranty - Elite warrants the RoboSlide for 3 years from the date of purchase.
• Shipping Weight - 104 lbs.
• Operator Dimensions - Length: 13.75", Width: 14.5", Height: 21.25".

• Battery - Sealed 12-volt, 7 amp hour battery for long life.
• Receiver - Built-in receiver included
• Control Board - Modular control board uses LED's to indicate all input and output functions of the operator.
• Reversing Sensor - If the gate hits a vehicle while closing it re-opens. If it hits a vehicle while opening it stops, reverses several inches and stops again.
• Timer - Can be set from 0 to 60 seconds.
• Safety Loop Input - RoboSlide is capable of accepting a safety loop system.
• Alarm - Alarm will sound anytime the moving gate is physically stopped by an unwanted object.
• Surge Suppressor Terminal - Surge suppressor included, protects against lightning.
• Electronic Inputs - Full-control system "open/stop/close", safety loop, photocell, telephone entry, and key switch.
• Optional Solar Input - The optional solar panel allows the RoboSlide to operate as an independent unit.

• RoboSlide Manual
• RoboSlide Brochure

• One operator
• One 20' #41 Gate Chain
• Sealed 12-volt, 7 amp hour battery for long life
• LiftMaster 312HM Security⁺ ERT Receiver - 315MHz
• Control board with Surge Suppressor Terminal
• Caution signs
• Installation/safety manual
• Picture of included parts

• Slave Operator - You will need another operator for master/slave installations (double gates).
• Optional Input Board - You will need this board for both operators in a master/slave set-up. This board is also required when using accessories such as a magnetic lock, third loop detector, and second photoeye for entrapment safety. Also required to use a 'open-close-stop' 3-button station.
• 18 VDC 2 Amp Plug-In Transformer - You will need one transformer for each operator unless you are using solar panels for power to the batteries.
• Transmitters - You will need a transmitter if you desire to open your gate with a remote. Any LiftMaster Security+ ERT 315MHz compatible transmitter will work. You can find transmitters here.
• Low Voltage Wire - This wire will be used between the transformer and control board. 14 gauge wire should be used for distances up to 1000'. For distances of 200' or less you can use 18 gauge wire. You will need to bury these wires in conduit. You can find this wire here. Direct burial landscape cable matching these specifications can also be used without conduit (available at most garden centers).
• Solar Panels - Solar panels can be can be used in remote areas. Solar panels can be found here.
• Accessories - More accessories can be found here. Included are loop detectors, keyswitches, photo eyes, telephone entry, intercoms, electric locks, keypads and much more.
• Read the RoboSlide manual for more information on the requirements for your particular application.

PRICES INCLUDE SHIPPING IN CONTINENTAL USA

Typical Elite RoboSlide Single Slide Gate Installation
(click to enlarge)

Typical Elite RoboSlide Double Slide Gate Installation
(click to enlarge)